>> Table: mpsTrunkGroupTable - (.1.3.6.1.4.1.272.4.53.3.3.1)

mpsTrunkGroupTable
OID	Name	Type	Access
.1	Index	TrunkGroupIndex	RW
.2	Layer2AlwaysOn	ENUM	RW
.3	DefaultTargetType	ENUM	RW
.4	DefaultTargetGroupIndex	GroupIndexOrZero	RW
.5	DefaultTargetExtensionIndex	ExtensionIndexOrZero	RW
.6	AdminStatus	ENUM	D
.7	OutSigMode	ENUM	RW
.8	BaseNumber	DisplayString	RW
.9	FixedOutNumber	DisplayString	RW
.10	DisplayName	DisplayString	RW
.11	Facilities	BITS	RW
.12	OutNumberType	ENUM	RW
.13	InterfaceType	ENUM	RW

Index

A unique value for each trunk group. Range: 1 to 65535

Layer2AlwaysOn

This value determine if the Layer2 for this external isdn port is always on (1) or off (2). Enumerations: true (1) false (2)

DefaultTargetType

This variable contains the target type for misdialing, default is group. 'none' means no routing (busy signalling). 'global' -> use system target 'mpsSysConfigDefaultTargetType'. Enumerations: group (1) extension (2) global (3) none (4)

DefaultTargetGroupIndex

This variable contains the default target group index if the mpsTrunkGroupDefaultTargetType = group (1). Range: 0 to 100

DefaultTargetExtensionIndex

This variable contains the default target extension index if the mpsTrunkGroupDefaultTargetType = extension(2). Range: 0 to 65535

AdminStatus

Just for MIB entry deletion. Enumerations: enable (1) delete (2)

OutSigMode

This variable contains the outgoing signalling mode for this TrunkGroup. standard(1) : standard signalling cnsGlobal(2) : for all outgoing calls, the global CLIP no screening number will be used. cnsIndividual(3): for outgoing calls, individual settings can be used. fixedDDI(4) : for all outgoing calls, the mpsTrunkGroupBaseNumber + mpsTrunkGroupFixedOutNumber will be used. Enumerations: standard (1) cnsGlobal (2) cnsIndividual (3) fixedDDI (4)

BaseNumber

This variable contains the base number of the point-to-point port. Length: 0 to 20

FixedOutNumber

This variable contains the number for fixed outgoing number signalling. 1. mpsTrunkGroupOutSigMode = fixedDDI : the fixed DDI for outgoing calls. 2. mpsTrunkGroupOutSigMode = cnsGlobal: the global CLIP no screening number. Length: 0 to 20

DisplayName

Display name of the trunk group. Length: 0 to 32

Facilities

Special facilities for trunks. ignoreBaseNumber : for P-P-trunks - ignore base number for incoming calls. suppressBaseNumber: for P-P-trunks - don't send base number for outgoing calls. cnsSendRemoteCallerNumber: An incoming external call is forwarded to extern via 2nd b-channel to this trunk group, the original (extern) party was send as calling party number instead of the outgoing number for this trunk. suppressNotify: don't send HOLD/RETRIEVE notifications to ISDN trunk. Enumerations: ignoreBaseNumber (0) suppressBaseNumber (1) cnsSendRemoteCallerNumber (2) suppressNotify (3)

OutNumberType

This variable contains the type of number of the calling party for outgoing calls. 'default' means the type of number will be set by the PBX, otherwise use unknown, subscriber or national for fix setting. Enumerations: default (1) unknown (2) subscriber (3) national (4)

InterfaceType

This variable contains the interface type, for which type of interface this trunk group can be used. isdn-pmp(1) : isdn extern, point-to-multipoint isdn-pp(2) : isdn extern, point-to-point voip-pmp(3) : VoIP extern, point-to-multipoint voip-pp(4) : VoIP extern, point-to-point pots(5) : analoque extern, FXO Enumerations: isdn-pmp (1) isdn-pp (2) voip-pmp (3) voip-pp (4) pots (5)