| IccId |
| The ICC-ID of the used SIM-Card to configure. Unfortunately some UMTS modem vendors offer no capability to read this ID before entering the valid PIN :-( Length: 0 to 32 |
| PIN |
| The PIN code of the SIM card. This is used to authorize the access to the SIM-Card. Length: 0 to 8 |
| PUK |
| The PUK code of the SIM card. Needed in case of wrong PIN input for three times in a row. Length: 0 to 16 |
| APN |
| GPRS APN (Access Point Name) used by this SIM-Card. Length: 0 to 80 |
| AccessMode |
| The default Access Type to be used by the GPRS/UMTS/LTE Modem. This setting depends on local network availability and therefore it's bound to the network operator specific SIM-Card. Possible settings are: auto(1) -- factory default settings gprs-only(2) -- GPRS only (no UMTS/LTE) umts-only(3) -- UMTS only (no GPRS/LTE) gprs-pref(4) -- GPRS preferred (Priority 2G/3G/xxx) umts-pref(5) -- UMTS preferred (Priority 3G/2G/xxx) lte-only(7) -- LTE only lte-pref(8) -- LTE preferred (Priority 4G/3G/2G) lte-umts(9) -- Priority 4G/3G, no GPRS lte-gprs(10) -- Priority 4G/2G, no UMTS lte-gprs-umts(11) -- Priority 4G/2G/3G umts-lte(12) -- Priority 3G/4G, no GPRS umts-gprs(13) -- Priority 3G/2G, no LTE umts-lte-gprs(14) -- Priority 3G/4G/2G gprs-lte(15) -- Priority 2G/4G, no UMTS gprs-umts(16) -- Priority 2G/3G, no LTE gprs-lte-umts(17) -- Priority 2G/4G/3G Not all possible settings make sense and/or are supported by all LTE capable Modems. Enumerations: - auto (1)
- gprs-only (2)
- umts-only (3)
- gprs-pref (4)
- umts-pref (5)
- delete (6)
- lte-only (7)
- lte-pref (8)
- lte-umts (9)
- lte-gprs (10)
- lte-gprs-umts (11)
- umts-lte (12)
- umts-gprs (13)
- umts-lte-gprs (14)
- gprs-lte (15)
- gprs-umts (16)
- gprs-lte-umts (17)
|
| RoamingMode |
| The Roaming configuration for this mobile interface. Possible values are: disabled - no roaming at all auto - roaming decision by modems factory defaults unrestricted - no restrictions for roaming decision international - international roaming only national - national roaming only fixed - use mobileConfigRoamingPLMN exclusively full-auto - let the modem select the roaming partner Enumerations: - disabled (1)
- auto (2)
- unrestricted (3)
- international (4)
- national (5)
- fixed (6)
- full-auto (7)
|
| RoamingPLMN |
| The PLMN (Public Land Mobile Netword) code used for Roaming. Used only if mobileDevCfgRoamingMode_fixed is selected. |
| Dispatch |
| The dispatch service the Modem should be used for. The SIM-Card should support/enable basic functionality to use the service (eg access circuit switched networks to use V.110 and/or V.120). Routing tasks (IP, IPX, X.25, bridging, ...) should use ppp(1). For isdnlogin program use the isdnlogin(2) item. For IPSec callback use item ipsec(60). Enumerations: - ppp (1)
- isdnlogin (2)
- none (3)
- ppp-modem (13)
- ppp-v110-1200 (15)
- ppp-v110-2400 (16)
- ppp-v110-4800 (17)
- ppp-v110-9600 (18)
- ppp-v110-14400 (19)
- ppp-v110-19200 (20)
- ppp-v110-38400 (21)
- ppp-v120 (23)
- ppp-modem-profile-1 (26)
- ppp-modem-profile-2 (27)
- ppp-modem-profile-3 (28)
- ppp-modem-profile-4 (29)
- ppp-modem-profile-5 (30)
- ppp-modem-profile-6 (31)
- ppp-modem-profile-7 (32)
- ppp-modem-profile-8 (33)
- ipsec (60)
|
| GsmFallback |
| If the Router is called using the GsmFallback number the actual connection is dropped and the Access Type is switched back from UMTS to GSM. Length: 0 to 32 |
| CugAddr |
| The provider assigned IP-Address if any. |
| CugAuth |
| The authentication method to be used. Enumerations: - none (1)
- pap (2)
- chap (3)
- pap-chap (4)
|
| CugUser |
| The provider assigned user name. Length: 0 to 255 |
| CugPwd |
| The provider assigned password. Length: 0 to 255 |
| OperatorScan |
| Handling of scanning available Providers (PLMN) never - use only home or fixed PLMN startup - scan on startup, only for information always - used for using roaming PLMN outside own country Enumerations: - never (1)
- startup (2)
- always (3)
|
| PinData |
| Not accessible entry for storing the PIN permanently. This is a security feature (?) used by France Telecom. Length: 0 to 16 |
| CugAPN |
| Closed User Group authentication APN, may be different from registration APN. Length: 0 to 80 |
| APNUser |
| Registration APN (Access Point Name) Username Length: 0 to 80 |
| APNPwd |
| Registration APN (Access Point Name) Password Length: 0 to 80 |