>> Table: capiConfigTable - (.1.3.6.1.4.1.272.4.7.6.1)

capiConfigTable
OID	Name	Type	Access
.1	StkNumber	INTEGER	R
.2	FaxG3RcvSpeed	ENUM	D
.3	FaxG3ECM	ENUM	RW
.4	FaxG3Header	ENUM	RW
.5	VoiceCoding	ENUM	RW
.6	SendAlerting	ENUM	RW
.7	V42bis	ENUM	RW
.8	ModemDefault	ENUM	RW
.9	FaxModulation	ENUM	RW
.10	Fax12000	ENUM	RW
.11	FaxTXLevel	ENUM	RW

StkNumber

The isdnStkNumber this configuration belongs to. Range: 0 to 31

FaxG3RcvSpeed

The G3 facsimile receive speed. For CM-EBRI this should be set to maximum. Set this field to `delete' to remove this entry. The entry can be deleted only if there is no entry with it's capiConfigStkNumber in the isdnStkTable. Enumerations: r4800 (1) r7200 (2) r9600 (3) r14400 (4) maximum (5) not-available (6) delete (7)

FaxG3ECM

Specifies whether ECM (error correction mode) should be used for G3 facsimile transmissions. Enumerations: on (1) off (2) not-available (3)

FaxG3Header

Specifies whether the header-line and logo ('BIANCA/FAX'), should appear on outgoing facsimiles. The value 'logo_header' allows the header-line and the logo to be printed on the top of each page. Enumerations: logo-header (1) no-logo (2) no-header (3) not-available (4)

VoiceCoding

Switches the bit order for voice-data. Enumerations: normal (1) reverse (2)

SendAlerting

For CAPI 1.1 this specifies when the CAPI server should send alert messages for incoming calls. Enumerations: never (1) ever (2) voice-only (3)

V42bis

Specifies whether V.42bis data compression should be used. If data compression is activated here,the receiving or sending side is first queried whether it supports data compression. The BRICK supports V.42bis data compression using up to 2 B-channels. Enumerations: on (1) off (2) not-available (3)

ModemDefault

Specifies the modem profile of the mdmProfileTable which contains the default modem parameters to use for modem connections. Enumerations: modem-profile-1 (1) modem-profile-2 (2) modem-profile-3 (3) modem-profile-4 (4) modem-profile-5 (5) modem-profile-6 (6) modem-profile-7 (7) modem-profile-8 (8)

FaxModulation

Set the default transmission protocol for fax. - v17 max. 14400 Bps new standard - v33 max. 14000 Bps early standard - v29 max. 9600 Bps fax standard - v17s v17 with Swiss capability - v33s v33 with Swiss capability Enumerations: v17 (1) v33 (2) v29 (3) v17s (5) v33s (6)

Fax12000

Enable or disable the 12000Bps Mode for fax transmission. A lot of fax receivers have problems with this tranmission mode. Default value is off Enumerations: on (1) off (2)

FaxTXLevel

Set the transmit level to -x dB db0 = 0dB, db3 = -3dB. In Germany -6dB (db6) is normally used for facsimile transmission. Enumerations: db0 (1) db3 (2) db6 (3) db9 (4) db12 (5) db15 (6)