| AtmIfIndex |
| The interface index of the associated ATM hardware. |
| Vpi |
| The VPI value of this Virtual Path Connection. Range: 0 to 255 |
| Vci |
| The VCI value of this Virtual Channel Connection. Range: 0 to 65535 |
| FlowType |
| The OAM hierarchical flow levels: see ITU I.610 Enumerations: - f5-segment (1)
- f5-end2end (2)
- f4-segment (3)
- f4-end2end (4)
|
| LoopbackTxCells |
| The number of OAM loopback cells that have been sent to the target in this sequence. |
| LoopbackRxCells |
| The number of OAM loopback cells that have been received from the target in this sequence. |
| LoopbackPending |
| The number of currently outstanding OAM loopback responses. |
| LoopbackCorr |
| The correlation of the last sent loopback message. |
| AisState |
| The AIS state is set to on(2) after receiving an AIS cell or detection of LOC (Loss of Continuity). The Ais state is set to off(1) either when receiving user cells (same VCC context) or via timeout. Enumerations: |
| AisTxCells |
| The number of OAM alarm indication signal (AIS) cells that have been transmitted since last change of AisState. |
| AisRxCells |
| The number of OAM alarm indication signal (AIS) cells that have been received since last change of AisState. |
| TotalAisTxCells |
| The total number of OAM alarm indication signal (AIS) cells that have been transmitted. |
| TotalAisRxCells |
| The total number of OAM alarm indication signal (AIS) cells that have been received. |
| RdiState |
| The RDI state is set to on(2) after receiving a RDI cell. The RDI state is to off(1) via timeout. Enumerations: |
| RdiTxCells |
| The number of OAM remote defect indication (RDI) cells that have been transmitted since last change of RdiState. |
| RdiRxCells |
| The number of OAM remote defect indication (RDI) cells that have been received since last change of RdiState. |
| TotalRdiTxCells |
| The totoal number of OAM remote defect indication (RDI) cells that have been transmitted. |
| TotalRdiRxCells |
| The total number of OAM remote defect indication (RDI) cells that have been received. |
| CCActivatorState |
| The status of the initiated CC negotiation, inactive(1) is the initial status, wait-act-con(2) is set after sending an CC activation request, active(3) is reached after receiving the CC activation confirmation whereas wait-deact-con(4) is used to indicate awaiting the CC deactivation confirmation. Enumerations: - inactive (1)
- wait-act-con (2)
- active (3)
- wait-deact-con (4)
|
| CCActivatorDirection |
| The direction of action indicated by a received CC activation confirmation, source(1) correlates with 'A-B', sink(2) with 'B-A' and both(3) with 'A-B' and 'B-A'. Enumerations: - sink (1)
- source (2)
- both (3)
- not-applicable (4)
|
| CCActivatorCorr |
| The correlation of the last CC activation message sent to the responder. |
| CCResponderState |
| The status of the passive CC negotiation, inactive(1) is the initial status, active(3) is reached after receiving an CC activation request whereas wait-deact-con(4) is used to indicate awaiting the CC deactivation confirmation. Enumerations: - inactive (1)
- active (3)
- wait-deact-con (4)
|
| CCResponderDirection |
| The direction of action indicated by a received CC activation request, source(1) correlates with 'B-A', sink(2) with 'A-B' and both(3) with 'A-B' and 'B-A'. Enumerations: - source (1)
- sink (2)
- both (3)
- not-applicable (4)
|
| CCResponderCorr |
| The correlation of the received CC activation message. |
| CCTxCells |
| The number of OAM continuity check cells that have been sent to the target in this sequence. |
| CCRxCells |
| The number of OAM continuity check cells that have been received from the target in this sequence. |